NPA20DA Terminal Control System

============================= System Information Command
?/HELP                        Print Help Information
STATUS                        Print System Status And Port Status
UPTIME                        Print System Uptime
============================= System Control Command
PON                           Power On, System Run On Normal State
POFF                          Power Off, System Run On Power Save State
PWLED FOLLOW ON/OFF           ON:Set System Power Led Follow LCD Status
                              OFF:Set System Power Led Not Follow LCD Status,
                              In Power On State,Power LED Always On
RESET                         Reset System Settings To Default
                              (Should Type "Yes" To Confirm, "No" To Discard)
RESET ALL                     Reset System And Network Settings To Default
                              (Should Type "Yes" To Confirm, "No" To Discard)
REBOOT                        Set System Reboot
AUTO STB xx                   Set System Auto Standby Time
                              xx=0:Auto Standby Off
                              xx=[1...120]:Auto Standby Time(mins)
AMPMODE xx                    Set Amp Power To xxx
                              xx=1:PoE+ Type 2 Class 4 (25.5W)
                              xx=2:PoE Class 0 (13W)
KEY ON/OFF                    Set System KEY Control On Or Off
LCD ON/OFF/15/30/60           Set LCD Always On Or Auto Turn Off In 15/30/60s
IDLED ON/OFF/15/30/60         Set ID LED On Or Auto Turn Off In 15/30/60s
TRIG ON/OFF yy                Set Trigger On Or Off With Trigger Level:yy
                              yy=0:Low Level(0V) Mute Output
                              yy=1:High Level(5 - 12V) Mute Output
RSB xx                        Set RS232 Baud Rate To xx bps
                              xx=[1...3]:1:4800,2:9600,3:19200
                              xx=[4...6]:4:38400,5:57600,6:115200
                              (Low Level(0V) Enable Amplifier Output,
                              High Level(5 - 12V) Disable Amplifier Output)
============================= Input Control Command
IN GAIN yy                    Set Input Gain To yy
                              yy=[-12...12]:Input Gain Value
IN GAIN+                      Increase Input Gain
IN GAIN-                      Decrease Input Gain
============================= Output Control Command
OUT xx VOL yy                 Set Output:xx Volume to yy
                              xx=[0...1]:0:ALL,1:AMP
                              yy=[0...100]:Volume Value
OUT xx VOL+                   Increase Output:xx Volume
                              xx=[0...1]:0:ALL,1:AMP
OUT xx VOL-                   Decrease Output:xx Volume
                              xx=[0...1]:0:ALL,1:AMP
OUT xx MUTE ON/OFF            Set Output:xx Mute On Or Off
                              xx=[0...1]:0:ALL,1:AMP
OUT xx DLYT yy                Set Output Delay Time To yy(ms)
                              xx=[0...1]:0:ALL,1:AMP
                              yy=[0...200]:Delay Time, Millisecond
OUT xx REVB ON/OFF            Set Output Reverb On Or Off
                              xx=[0...1]:0:ALL,1:AMP
OUT xx PHASE yy INV ON/OFF    Set Output L-Invert Or R-Invert On Or Off
                              xx=[0...1]:0:ALL,1:AMP
                              yy=[0,1]:0:LEFT,1:RIGHT
OUT xx MIX yy                 Set Output Mix yy
                              xx=[0...1]:0:ALL,1:AMP
                              yy=[1,2]:1:STEREO,2:LEFT-CH
                              yy=[3,4]:3:RIGHT-CH,4:LEFT-CH and RIGHT-CH
OUT xx EQ yy VAL zz           Set Output GEQ:yy To zz
                              xx=[0...1]:0:ALL,1:AMP
                              yy=[1...31]:EQ Index
                              zz=[-10...3]:EQ Value
OUT xx EQ PRESET yy           Set Output GEQ To Preset:yy
                              xx=[0...1]:0:ALL,1:AMP
                              yy=[1...3]:1:Flat,2:Custom1,3:Custom2
============================= Network Control Command
NET DHCP ON/OFF               Set Auto IP(DHCP) On Or Off
NET IP xxx.xxx.xxx.xxx        Set IP Address
NET GW xxx.xxx.xxx.xxx        Set Gateway Address
NET SM xxx.xxx.xxx.xxx        Set Subnet Mask Address
NET TCPPORT ON/OFF            Set TCP/IP On Or Off
NET TCPPORT xxxx              Set TCP/IP Port
NET TN ON/OFF                 Set Telnet On Or Off
NET TN xxxx                   Set Telnet Port
NET RB                        Network Reboot And Apply New Config!!!
NET DNS xxxx                  Set DNS Domain Name To xxxx